Featured

Ls inverter easy start guide Connection diagram Ls inverter IG5A Parameter Setting.etc tv



Published
Ls inverter easy start guide. Connection diagram Ls inverter.IG5A Parameter Setting,
how to parameter setting inverter for iG5A, step by step description, with wiring connection,
Input: R S T
Output: U V W - Motor ConnectionWhat is an Inverter?
An inverter converts the DC voltage to an AC voltage. In most cases, the input DC voltage is usually lower while the output AC is equal to the grid supply voltage of either 120 volts, or 240 Volts depending on the country.

The inverter may be built as standalone equipment for applications such as solar power, or to work as a backup power supply from batteries which are charged separately.

The other configuration is when it is a part of a bigger circuit such as a power supply unit, or a UPS. In this case, the inverter input DC is from the rectified mains AC in the PSU, while from either the rectified AC in the in the UPS when there is power, and from the batteries whenever there is a power failure.

There are different types of inverters based on the shape of the switching waveform. These have varying circuit configurations, efficiencies, advantages and disadvantages

An inverter provides an ac voltage from dc power sources and is useful in powering electronics and electrical equipment rated at the ac mains voltage. In addition they are widely used in the switched mode power supplies inverting stages. The circuits are classified according the switching technology and switch type, the waveform, the frequency and output waveform.

Basic inverter operation
The basic circuits include an oscillator, control circuit, drive circuit for the power devices, switching devices, and a transformer.

The conversion of dc to alternating voltage is achieved by converting energy stored in the dc source such as the battery, or from a rectifier output, into an alternating voltage. This is done using switching devices which are continuously turned on and off, and then stepping up using the transformer. Although there are some configurations which do not use a transformer, these are not widely used.

The DC input voltage is switched on and off by the power devices such as MOSFETs or power transistors and the pulses fed to the primary side of the transformer. The varying voltage in the primary induces an alternating voltage at secondary winding. The transformer also works as an amplifier where it increases the output voltage at a ratio determined by the turn’s ratio. In most cases the output voltage is raised from the standard 12 volts supplied by the batteries to either 120 Volts or 240 volts AC.

The three commonly used Inverter output stages are, a push-pull with centre tap transformer, push-pull half-bridge, or push-pull full bridge. The push pull with centre tap is most popular due to its simplicity and, guaranteed results; however, it uses a heavier transformer and has a lower efficiency.

A simple push pull DC to AC inverter with centre tap transformer circuit is a shown in the figure below.

what is an inverter?
Figure 1 basic inverter switching circuit

Inverter output waveforms
The inverters are classified according to their output waveforms with the three common types being the square wave, the pure sine wave and the modified sine wave.

The square wave is simple and cheaper, however, it has a low power quality compared to the other two. The modified square wave provides a better power quality (THD~ 45%) and is suitable for most electronic equipment. These have rectangular pulses that have dead spots between the positive half cycle and the negative half cycle (THD about 24%).

What is an inverter
Figure 2: Modified sine waveform

The true sine wave inverter has the best waveform with the lowest THD of about 3%. However, It is the most expensive and used in applications such as medical equipment, stereos, laser printers and other applications requiring sinusoidal waveforms. These are also used in the grid ties inverters and grid connected equipment

What is an inverter
Figure 3: Pure Sine wave

Applications
Inverters are used for a variety of applications that range from small car adapters to household or office applications, and large grid systems.

Uninterruptible power supplies
As standalone inverters
In solar power systems
As a building block of a switched mode power supply
ig5a basic setting,vfd,vfd motor control,vfd drive training,vfd control wiring,vfd motor control circuit diagram,ls inverter,ls vfd control wiring,ls vfd,elab industrial electronics,vfd parameter setting,variable frequency drive,inverter parameter setting,Ls inverter easy start guide,Connection diagram Ls inverter,IG5A Parameter Setting,Engineering Technology BD,Basic inverter operation,what is an inverter?,ls vfd ig5a setup,easy start guide
Ls inverter easy start guide Connection diagram Ls inverter IG5A Parameter Setting.etc tv
Category
Audio
Be the first to comment